WERK.01
REV. 2026.07
Componentry for 700hp+ platforms

Built for cars that outrun their factory limits.

Homologated aero, forged wheels, and titanium exhaust for Porsche 911 Turbo, 918, Cayman GT4, and comparable hypercar platforms. Every part shipped with dyno data and a torque spec sheet — nothing guessed, nothing generic.

04Systems Covered
−38kgAvg. Weight Saved
+61Whp Gain, Stage 2
CoCCertified Fitment
4,545 MM WHEELBASE REF. 01 — REAR WING 02 — FORGED WHEEL 03 — DIFFUSER

Downforce, without the drag penalty

Wind-tunnel validated at 200+ km/h. Carbon-fiber weave, autoclave cured, matched to factory hardpoints.

PN AE-118RIN STOCK

Swan-Neck Rear Wing

Adjustable dual-plane wing on swan-neck mounts, clearing the underside for cleaner airflow to the diffuser.

MaterialDry Carbon 3K
Downforce @ 250km/h184 kg
Weight4.1 kg
Adjustment3-position
PN AE-204FIN STOCK

Front Splitter + Canards

Extended splitter lip with flanking canards to balance front-axle lift at speed against the rear wing.

MaterialCarbon / Kevlar
Front Lift Reduction−41%
Ground Clearance92 mm
MountingOEM hardpoint
PN AE-330DBUILT TO ORDER

Rear Diffuser, 5-Channel

Five-channel underbody diffuser accelerating exit airflow, engineered as a matched set with the swan-neck wing.

MaterialDry Carbon 3K
Channels5
Rear Lift Reduction−33%
Lead Time3–4 weeks

Unsprung mass is the mass that matters

Forged monoblock and two-piece wheels, paired with big-brake kits sized to fill them properly.

PN WH-501IN STOCK

Forged Monoblock 21"

One-piece forged rotary construction. Roughly a third lighter than the factory cast wheel it replaces.

Sizes20"F / 21"R
Weight Saved−6.8 kg / corner
MaterialForged 6061-T6
FinishSatin Graphite
PN BR-742IN STOCK

Carbon-Ceramic Big Brake Kit

10-piston front / 4-piston rear calipers over two-piece carbon-ceramic rotors, built to resist fade on repeated hot laps.

Rotor Diameter410 mm
Fade Resistance15+ hot laps
Weight Saved−9 kg / axle
Caliper FinishGuards Red
PN WH-518BUILT TO ORDER

Two-Piece Track Wheel

Center-lock, two-piece design with a replaceable barrel — built for teams who curb wheels more than they'd like to admit.

Sizes19"F / 20"R
BarrelReplaceable
Load Rating1,050 kg
Lead Time5 weeks

Every gram out of the tail end pays back

Titanium and Inconel construction, valved for a quiet cold-start and full voice above 4,000 rpm.

PN EX-090IN STOCK

Titanium Valved Catback

Full titanium system from the cats back, electronic valves controlled from a steering-wheel switch.

MaterialGrade 2 Titanium
Weight Saved−12.4 kg
Power Gain+18 whp
SoundValved, 2-mode
PN EX-112IN STOCK

Inconel Header Set

Equal-length Inconel headers for even exhaust pulse spacing and reduced backpressure at high RPM.

MaterialInconel 625
Runner LengthEqual, tuned
Power Gain+24 whp
Heat Rating982°C
PN EX-1402 LEFT

High-Flow Sport Cats

200-cell high-flow catalysts, keeping emissions compliance while opening up the top end of the rev range.

Cell Density200 CPSI
Flow Increase+31%
ComplianceEuro 6d
FitmentDirect bolt-on

Tuned for the road you actually drive

Coilovers and bracing engineered as a set, not sold as isolated parts — geometry stays correct across the whole range.

PN CH-220IN STOCK

3-Way Adjustable Coilovers

Independent compression, rebound, and ride-height adjustment, with front and rear corner balance matched at install.

AdjustmentCompr. / Rebound / Height
Ride Height Range−15 to −45 mm
Spring RateProgressive, dual
ApplicationStreet / Track
PN CH-266IN STOCK

Front Strut Tower Brace

Billet-machined brace tying the front strut towers together, cutting flex under hard cornering loads.

MaterialBillet 6061
Chassis Stiffness+11%
Weight1.3 kg
FinishAnodized Black
PN CH-301BUILT TO ORDER

Adjustable Rear Sway Bar

Three-position rear sway bar for dialing in oversteer/understeer balance to match tire and track conditions.

Positions3
Diameter24 mm
MaterialHollow Chromoly
Lead Time2 weeks

Rough out a package before you call

Sliders give a directional estimate only — final numbers depend on your specific chassis and options.

Stage Estimator

Drag each system to a target intensity. The readout on the right updates with an estimated whp gain, weight saved, and package price band.

Request Full Spec Sheet
Est. Power Gain+18 whp
Est. Weight Saved−7 kg
Est. Downforce Added+40 kg
Est. Lead Time3–4 weeks
Package Estimate$14,200 – $18,000
Web hosting by Somee.com